3.3.1. Technical characteristics
| Marking of the engine |
5S-FE
|
| Volume |
2,2 liters
|
| Compression pressure in cylinders | |
| Standard |
178 psi
|
| Minimum |
142 psi
|
| Oil pressure (the engine is warmed) | |
| Idling |
4,3 psi at least
|
| At 3000 rpm |
36 – 71 psi
|
| Head of cylinders | |
| Maximum admissible deformation: | |
| – the surface which is joined to the block of cylinders |
0,051
|
| – the surfaces which are joined to collectors |
0,079
|
| Valves and elements of valves | |
| Valve border width: | |
| – standard |
0,794 – 1,191
|
| – minimum |
0,508
|
| Diameter of a rod of the valve: | |
| – inlet |
5,969 – 5,984
|
| – final |
5,964 – 5,979
|
| Gap between a rod of the valve and the directing plug | |
| Inlet valve: | |
| – standard |
0,026 – 0,061
|
| – limit |
0,079
|
| Final valve: | |
| – standard |
0,031 – 0,066
|
| – limit |
0,099
|
| Valve spring | |
| The maximum deviation from a right angle |
2,007
|
| Length in a free state |
40,950 – 42,799
|
| Length in the established state |
34,697
|
| Valve elevator | |
| Diameter |
30,965 – 30,975
|
| Diameter of a nest |
31,001 – 31,019
|
| Lubricant gap | |
| Standard |
0,023 – 0,051
|
| Limit |
0,071
|
| Bent shaft and rods | |
| Rod bearing: | |
| – diameter |
51,984 – 51,999
|
| – maximum conicity and ovality |
0,020
|
| Lubricant gap: | |
| – standard |
0,023 – 0,056
|
| – limit |
0,079
|
| Side gap (free wheeling) of a rod: | |
| – standard |
0,160 – 0,313
|
| – limit |
0,351
|
| Radical bearing: | |
| – diameter |
54,999 – 55,004
|
| – maximum conicity and ovality |
0,020
|
| – maximum admissible wear |
0,061
|
| Lubricant gap (standard): | |
| – N3 bearing (central) |
0,026 – 0,043
|
| – other bearings |
0,015 – 0,033
|
| – limit |
0,079
|
| Free wheeling of a bent shaft: | |
| – standard |
0,020 – 0,221
|
| – limit |
0,300
|
| – thickness of a persistent washer |
2,441 – 2,481
|
| Balancing device of the engine | |
| Free wheeling between balancing shaft of N1 and N2 |
0,005 – 0,061
|
| Free wheeling between a balancing shaft of N1 and a bent shaft |
0,026 – 0,089
|
| Axial gap of a balancing shaft: | |
| – standard |
0,061 – 0,109
|
| – limit |
0,109
|
| Block of cylinders | |
| Maximum admissible deformation of a surface of the block of cylinders |
0,051
|
| Diameter of the cylinder: | |
| – standard: | |
| • marking 1 |
87,000 – 87,010
|
| • marking 2 |
87,010 – 87,020
|
| • marking 3 |
87,020 – 87,030
|
| – limit |
87,229
|
| – the most admissible conicity and ovality of the cylinder |
0,020
|
| Pistons, piston rings | |
| Diameter of the piston: | |
| – marking 1 |
86,850 – 86,860
|
| – marking 2 |
86,860 – 86,871
|
| – marking 3 |
86,871 – 86,881
|
| Gap between the piston and the cylinder: | |
| Standard |
0,138 – 0,160
|
| Limit |
0,180
|
| Trailer gap of a piston ring: | |
| – top compression ring | |
| • standard |
0,269 – 0,500
|
| • limit |
1,100
|
| – average compression ring: | |
| • standard |
0,351 – 0,600
|
| • limit |
1,199
|
| – oil scraper ring: | |
| • standard |
0,201 – 0,551
|
| • limit |
1,151
|
| Gap between a piston ring and a side surface of a flute of a ring: | |
| – first ring |
0,041 – 0,079
|
| – second ring |
0,031 – 0,071
|
Moments of an inhaling of threaded connections, N. of m.
| Bolts of covers of radical bearings |
58
|
| Nuts of covers of rods: | |
| – step 1 |
25
|
| – step 2 |
Tighten for 90 °
|
| Bolts of the balancing device |
49
|